New project

[Grr]

ha, yeah my car is like that too, once its on the ground theres plenty of clearance. That aluminum is tricky isnt it! now and then ill be cruising along nice, then BAM, big ass hole in it

[XJHEAD]

Yanked the mock-up motor last night and pulled the tranny. The tranny will be dropped off at T-N-T Tranmission on Monday just to be checked out. Ted does a hell of a job. Had him do the re-build last summer right after P-10. Had a few runs on it then had it out for other things and he told me to bring it over just so he could take a look. Tore it down, everything looked good, so I put it back in. Figured it was out now so I would have him take another peak at it. Anyways the motor should be ready to be picked up early next week. Still have a lot of wiring to do and some suspension changes yet. I still haven't decided if I am going to change gears or not. Either I'll keep the 3.27's in it or put some 3.08's in it. I did make a custom Tranny crossmember for it the other night. I couldn't get my little Miller 135 to get very good penetration so I dropped it off over to 63Vette for a little tig action.

Built with a cutting torch and a BFH

[XJHEAD]

Got the motor back last night. Hopefully start bolting some stuff to it in the coming days.

Had them stuff some Oliver rods in it, they must have been a little beefier than the Eagles, it took 4 slugs of heavy metal.

[zbrown]

looks great........ holy F those valve covers seem tall

[z31]

Looks good. :icon_cheers: Did you make the oil pan?

[Cobra Rob]

As a trained welder you guys look like you know what you are doing

[XJHEAD]

z31;274684 wrote:
Looks good. :icon_cheers: Did you make the oil pan?

I made it black.. It is a Canton piece "of shit". Another thing that takes a hammer to make fit. Any manufacturer that says bolt-on is a liar.

Cobra Rob;274689 wrote:
As a trained welder you guys look like you know what you are doing

One of us maybe, and it's not me.

[z31]

You going to put your car in the all Ford car show at the track?

[XJHEAD]

z31;274695 wrote:
You going to put your car in the all Ford car show at the track?

I was planning on it. Even if not running but it is rollable, I will take it over there.

[63vette]

XJHEAD;274697 wrote:
I was planning on it. Even if not running but it is rollable, I will take it over there.
Pretty common for Fords to be pushed to car shows. Bong!!!!!

[63vette]

XJHEAD;274693 wrote:
One of us maybe, and it's not me.

I can weld aluminum between 3 and 5 beers. Any less or any more and I cant. :icon_scratch::icon_scratch::icon_scratch:

[Grr]

im in the same boat, i shake too much to weld alum properly unless i have a couple beers first, lol

[XJHEAD]

Before I put the intake on I figured it was a good idea to port match it. I took about an 1/8" off two sides of each port. Should have done that along time ago. Had to trim the gaskets too. Wrapped headers last night and tonight. Pulled turbos apart to check them out and cleaned them up.

[Cobra Rob]

as a mustang lover this is very sick keep up the good work

[z31]

That intake elbow going to clear the hood? :icon_scratch:

[z31]

What kinda power will that motor make without the turbos?

[XJHEAD]

z31;274970 wrote:
That intake elbow going to clear the hood? :icon_scratch:

Hope so, if not I'll get the chop saw out.

z31;274971 wrote:
What kinda power will that motor make without the turbos?

When it was N/A it did 485 rwhp @ 6,000

[Trafik Jamz]

Looks exactly like it did last time I saw it Bill...

of course that was 30mins before you posted these

[Grr]

z31;274970 wrote:
That intake elbow going to clear the hood? :icon_scratch:

just be sure to latch the hood when you take it out for the first time, wouldnt want any accidents like some people that will remain nameless......

[XJHEAD]

Motor is in.